Elettrogas kraner og Evesco pumper - RASMUSSEN ENGROS AS

Nyheter fra Båtmagasinet

Elettrogas kraner og Evesco pumper

Elettrogas kraner er laget for det maritime miljø.

Elettrogas kraner er en unik serie kraner for de fleste typer båter.

Bilde av 520603[1]

Bilde av 520628[1]

Bilde av 520626[1]

Se mere info hos denne leverandør: www.aravon.it

13S Armatur laget av forkrommet messing. Tåler trykk opp til 4,0 bar. Slangekobling må bestilles separat. Montering hulldiameter: 18 mm
15 Armatur laget av forkrommet messing. Tåler trykk opp til 4,0 bar. Slangekobling må bestilles separat. Montering hulldiameter: 18 mm Høyde: 65 mm
17 Armatur laget av forkrommet messing. Tåler trykk opp til 4,0 bar. Slangekobling må bestilles separat. Montering hulldiameter: 18 mm
28B Armatur laget av forkrommet messing. Tåler trykk opp til 4,0 bar. Slangekobling må bestilles separat. Montering hulldiameter: 30 mm Avtakbart tut, tuten kan svinges.
28N Armatur laget av forkrommet messing. Tåler trykk opp til 4,0 bar. Slangekobling må bestilles separat. Montering hulldiameter: 40 mm
Tilbehør
Kit 04 Armatur laget av forkrommet messing. Tåler trykk opp til 4,0 bar. Slangekobling må bestilles separat. Hulldiameter montering: 100 mm Totalmål: b: 130 mm h: 130 mm Leveres med slange og dusjhåndtak Enkel å montere, bare et hull Alt samlet i en boks
2580
34C Armatur laget av forkrommet messing. Tåler trykk opp til 4,0 bar. Slangekobling må bestilles separat. Hulldiameter montering: 35 mm Med keramiske pakninger Svingbar tut L=200mm H=106mm
34L Armatur laget av forkrommet messing. Tåler trykk opp til 4,0 bar. Slangekobling må bestilles separat. Hulldiameter montering: 35 mm Med keramiske pakninger Svingbar tut L=200mm H=106mm

46Marine 46Minimal Armatur laget av forkrommet messing. Tåler trykk opp til 4,0 bar. Slangekobling må bestilles separat. Hulldiameter montering: 20 mm Svingbar tut Bare kaldt vann L = 160 mm H = 182 mm ( stående) H = 37mm ( liggende)
47Marine 47Minimal Armatur laget av forkrommet messing. Tåler trykk opp til 4,0 bar. Slangekobling må bestilles separat. Hulldiameter montering: 20 mm


Evesco Pumper
Our EVESCO diaphragm hand bilge pumps has been designed for yachtsmen by Yachtsmen. Only the very best materials has been used to give absolute best performance and long trouble free life. The pump-body, back , rocker-arm and inspection screw-cover are made of strong tough plastics. All rubber parts are made of tough oil resistant Nitrile rubber. All bolts, nuts and the pump handle are made of stainless steel AISI-329. We have constructed our pumps to be used in all Pleasure crafts and Life boats where high output is required. The pumps are used as bilge pumps, wastetankpumps, diesel pumps etc. All pumps are cleaned inside in seconds without any use of tools—just unscrew the inspection front cover by hand. Flow direction can be altered in 8 different directions. Just unscrew the 8 bolts and nuts and turn the Flow direction as wanted and fix the bolts and nuts again.

EVESCO can’t rust – body made of tough nylon and delrin – back made of seawater resistant aluminium cowered with nylon – ball-bearing, bolts and nuts made of stainless steel excentric made of special brass – motor from bosch – diaphragm and valves made of nitrile rubber. EVESCO is constructed as bilge-, toilet– and wastetankpump and allows dirt etc. To pass through the pump without any notice in capacity. EVESCO is cleaned inside in seconds without any use of tools – just unscrew the front cover by hand. EVESCO is a robust pump which can be running with or without water. EVESCO can be supplied with an automatic switch which will start the pump at high waterlevel and shut the pump again at low waterlevel. We can recommend this switch installationfor your safety. EVESCO is as standard supplied with horizontal flow, but the construction allow to alter this by loosing bolts and nuts and turn the body the way you want. Motor must always be mounted in top. If pump is used in connection with toilet or waste tank, the flow direction must be vertical with suction from below.